Proudly making Quest AV equipment in Australia since 1988
®
abn 99 064 323 255  also t/a Quest Electronics ®  and Quest AV ®
Phone and SMS ... 0431 920 667 Mail ... POB 348  Woy Woy  NSW   2256
®
SPECIFICATIONS INPUT Connector: 15 pin high-density female D-sub RGB signals: Analogue video, 0.7-1.0Vp-p, 75ohm term. H & V Sync: TTL level, horizontal & vertical, 2K2 pull-up MONITOR OUTPUT Connector: 15 pin high-density female D-sub RGB Gain: Buffered,   unity   ±10%,   fixed   gain,   to   feed   75 ohm   inputs,   maximum   recommended   cable length 20Mtrs H & V Sync: Buffered,   TTL   compatible,   polarity   same   as input, protected against short-circuit RGB BW: >240MHz
The     Quest     AV     model     VGS2     Graphics Splitter   is   small,   efficient,   inexpensive,   very easy    to    use    and    works    very    nicely    with VGA,   SVGA,   XGA,   WVGA ,   etc.   Because the   VGS2   runs   from   a   12Vdc   supply,   it   can readily   be   used   in   portable   applications   or in remote locations. With    the    CST1    remote    switch     assembly (optional    extra)    you    can    make    the    extra output   go   completely   black   while   you   load files,   change   software,   or   just   to   attract   your audience's    attention    back    to    you,    and    all without   affecting   your   monitor   in   any   way and   without   showing   unintended   pictures... Very professional! The   VGS2   comes   ready   to   use!   Supplied with   a   high   quality   cable   to   connect   to   your PC   or   laptop   and   an   Australian   approved 12Vdc      power      supply.      There      are      no adjustments,    dummy    plugs    or    confusing miniature   switches   to   configure,   just   plug   it in and use it right away. You   can't   go   wrong   -   the   connectors   are clearly    labelled    to    prevent    confusion.    No damage   can   be   done   to   the   VGS2   or   your PC   and   monitors,   projectors,   LCD   displays, etc.    if    incorrectly    connected    as    all    inputs and outputs are protected. We   have   off-the-shelf   HQ   cables   available or   you   can   use   standard   75   ohm   BNC   video cables    in    conjunction    with    our    very    neat little      DB95       adaptors      for      super-long distances.
VGS2 High Resolution 1 in, 2 out VGA Splitter with Blanking function Run two screens from a single computer Impressive presentations Effective teaching aid Wide bandwidth and low loss Crystal clear, 240MHz BW 
BOOSTED OUTPUT Connector: 15 pin high-density female D-sub RGB Gain: Buffered,   factory   set   to   unity,   up   to   +6dB gain          available     (Internal     R,G     &     B adjustments). H & V Sync: Buffered,   TTL    compatible,    polarity    same as input, protected against short-circuit RGB BW: -3dB   @   240MHz,   with   standard   0.7Vp-p signals into 75 ohm loads. GENERAL Features: Boosted    output    picture    can    be    blanked with   CST1   remote   control   cable   (not   incl) 12Vdc operation (9V - 30V range) Reverse polarity protected Included: Aust. approved 12Vdc adaptor (S1250) 1.2Mtr VGA input cable (HQ1K2) Optional: CST1 Remote control cable, 6Mtrs Long HQ VGA cables DB95 adaptor for really long cabling Optional Mod: Second    boosted    output    instead    of    fixed gain    monitor    output.    No    extra    charge    if specified at time of ordering. Dimensions: WxDxH:   140   x   115(max)   x   36mm,   VGS2 only, with no cables connected. Weight: Packed 980gms, VGS2 only 245gms.
VGS2 $179.00 inc GST Packing & Delivery are not included Spare power adaptor S1250 $15.99 + Del.